Specifications and technical data
Yamaha MT-07 700, 2014, 74,8 PS, 55 kw
Go to the store - view our offer for
spare parts for Yamaha MT-07 700, 2014, 74,8 PS, 55 kw
Year of manufacture
2014
No. of cylinders
2
Cylinder capacity
700 cc
Power
74,8 PS, 55 kw
Specifications and technical data
Engine
Engine speed at maximum power
9000 Revolutions per minute
Number of cylinders
2
Valves per cylinder
4
Engine
Firing order
1 - 2
Throttle grip free play
3.0 - 5.0 Millimetre
Ignition coil primary resistance
1.19 - 1.61 Ohms
Ignition coil secondary resistance
8500 - 11500 Ohms
Valve clearance
Cold engine
Inlet
0.11 - 0.20 Millimetre
Exhaust
0.24 - 0.30 Millimetre
Idle speed
1100 - 1300 Revolutions per minute
Fuel pump pressure
(At idle speed)
(At idle speed)
3.0 - 3.9 (bar)
Spark plugs (make and type)
NGK LMAR8A-9
Spark plug gap
0.8 - 0.9 Millimetre
Number of spark plugs
2
Compression pressure(Cylinder 1)
Normal pressure
(At 355 rpm)
(At 355 rpm)
8.8 (bar)
Minimum pressure
(At 355 rpm)
(At 355 rpm)
7.7 (bar)
Compression pressure(Cylinder 2)
Normal pressure
(At 355 rpm)
(At 355 rpm)
7.9 (bar)
Minimum pressure
(At 355 rpm)
(At 355 rpm)
6.9 (bar)
Oil pressure
(at 100 °C)
(at 100 °C)
2.8/5000
Engine
Cap pressure
1.08 - 1.37 (bar)
Thermostat opening temperature
80 - 84 (°C)
Thermostat fully open
95
Front disc brakes
Disc diameter, front
282.0 Millimetre
Disc thickness, front
4.5 Millimetre
Disc thickness, front, minimum
4.0 Millimetre
Brake pad thickness, front
4.5 Millimetre
Brake pad thickness, front, minimum
0.5 Millimetre
Disc run-out, maximum (front)
0.1 Millimetre
Rear disc brakes
Disc diameter, rear
245.0 Millimetre
Disc thickness, rear
5.0 Millimetre
Disc thickness, rear, minimum
4.5 Millimetre
Brake pad thickness, rear
6.0 Millimetre
Brake pad thickness, rear, minimum
1.0 Millimetre
Disc run-out, maximum (rear)
0.15
Wheels and tyres
Tyre size and pressure
Front tyre size
120/70 ZR17 M/C 58W
Front tyre pressure
2.2 (bar)
Front wheel rim size
3.5x17
Rear tyre size
180/55 ZR17 M/C 73W
Rear tyre pressure
2.5 (bar)
Rear wheel rim size
5.5x17
Speed index, minimum
(Based on the maximum speed as listed in the European Type Approval data sheets)
(Based on the maximum speed as listed in the European Type Approval data sheets)
H
Engine
Engine sump, including filter
Plug location
Initial filling
3.0 Litre
Refilling
2.6 Litre
Cooling system
1.9 Litre
Suspension
Front fork
Left fork leg
0.40 Litre
Right fork leg
0.40 Litre
Front fork
Left fork leg
162 Millimetre
Right fork leg
162 Millimetre
General
Fuel tank
14.0 Litre
Fuel tank, reserve
2.7
Final drive
Final drive chain (make and type)
DID 525VAZ
Final drive chain free play
51 - 56 Millimetre
Number of final drive chain links
108
Number of final drive front sprocket teeth
16
Number of final drive rear sprocket teeth
43
Clutch system
Clutch plate thickness
(A)
(A)
2.90 - 3.10 Millimetre
Clutch plate thickness
(B)
(B)
2.92 - 3.08 Millimetre
Clutch plate thickness, minimum
(A)
(A)
2.82 Millimetre
Clutch plate thickness, minimum
(B)
(B)
2.80 Millimetre
Clutch spring length
50.0 Millimetre
Clutch spring length, minimum
47.5 Millimetre
Clutch lever free play
5 - 10 Millimetre
Engine
Note: Always renew stretch bolts and self-locking nuts
Cylinder head(Threads and contact surface lightly oiled)
Renew the bolts
(Bolts 1 - 6)
(Bolts 1 - 6)
Renew the gasket
Stage 1
(Bolts 1 - 6)
(Bolts 1 - 6)
10 (Nm)
Stage 2
(Bolts 1 - 6)
(Bolts 1 - 6)
40 (Nm)
Stage 3
(Loosen and tighten the bolts one by one)
(Loosen and tighten the bolts one by one)
20 (Nm)
Stage 4
(Bolts 1 - 6)
(Bolts 1 - 6)
90 (°)
Stage 5
(Bolts 7 and 8)
(Bolts 7 and 8)
10 (Nm)
Cylinder head (studs)
15 (Nm)
Valve cover
(Renew the gasket)
(Renew the gasket)
10 (Nm)
Apply sealant
Big-end bearing cap(Threads and contact surface lubricated with molybdenum oil)
Stage 1
20 (Nm)
Stage 2
180 (°)
Crankcase
(Apply sealant)
(Apply sealant)
Crankcase(The tightening sequence is stamped on the crankcase)
Renew the bolts
(Bolts 1 - 6)
(Bolts 1 - 6)
Renew the O-rings
(Bolts 7 - 12)
(Bolts 7 - 12)
Threads and contact surface lightly oiled
(Bolts 13 - 27)
(Bolts 13 - 27)
Stage 1
(Bolts 1 - 6)
(Bolts 1 - 6)
24 (Nm)
Stage 2
(Loosen and tighten the bolts one by one)
(Loosen and tighten the bolts one by one)
17 (Nm)
Stage 3
(Bolts 1 - 6)
(Bolts 1 - 6)
60 (°)
Stage 4
(Bolts 7 - 14)
(Bolts 7 - 14)
24 (Nm)
Stage 5
(Bolts 15 - 27)
(Bolts 15 - 27)
10 (Nm)
Crankcase cover
(Renew the gasket)
(Renew the gasket)
12 (Nm)
Tighten the bolts in a criss-cross pattern
(Apply thread-locking compound)
(Apply thread-locking compound)
Sump
(Tighten the bolts in a criss-cross pattern)
(Tighten the bolts in a criss-cross pattern)
10 (Nm)
Renew the gasket
Engine oil drain plug
(Renew the gasket)
(Renew the gasket)
43 (Nm)
Spark plugs
13 (Nm)
Oil filter
17 (Nm)
Oxygen sensor
25 (Nm)
Starter motor
10 (Nm)
Camshaft bearing caps
10 (Nm)
Camshaft gearwheel
24 (Nm)
Timing chain tensioner
(Renew the gasket)
(Renew the gasket)
10 (Nm)
Timing chain guide
10 (Nm)
Flywheel
(Threads and contact surface lightly oiled)
(Threads and contact surface lightly oiled)
70 (Nm)
Exhaust manifold
(Renew the gasket)
(Renew the gasket)
20 (Nm)
Coolant pump housing
10 (Nm)
Fuel pump
(Renew the gasket)
(Renew the gasket)
4 (Nm)
Tighten the bolts in a criss-cross pattern
Fuel rail
3.5 (Nm)
Fuel tank
7 (Nm)
Thermostat housing
12 (Nm)
Coolant drain plug
(Renew the washer)
(Renew the washer)
7 (Nm)
Oil pump
12 (Nm)
Oil pump
(Cover)
(Cover)
3.8 (Nm)
Oil pump chain guide
10 (Nm)
Front disc brakes
Brake master cylinder clamp
10 (Nm)
Front brake caliper
40
Brake hose to caliper
(Renew the gasket)
(Renew the gasket)
30 (Nm)
Front brake disc
18 (Nm)
Renew the bolts
Apply thread-locking compound
Tightening sequence:
(Tighten the bolts in a criss-cross pattern)
(Tighten the bolts in a criss-cross pattern)
Rear disc brakes
Rear brake caliper guide bolt
27 (Nm)
Rear brake caliper
(Apply thread-locking compound)
(Apply thread-locking compound)
22 (Nm)
Brake hose to caliper
(Renew the gasket)
(Renew the gasket)
30 (Nm)
Rear brake disc
30 (Nm)
Renew the bolts
Apply thread-locking compound
Tightening sequence:
(Tighten the bolts in a criss-cross pattern)
(Tighten the bolts in a criss-cross pattern)
Brake pad retaining pin
17 (Nm)
Clutch system
Clutch
(Renew the nut)
(Renew the nut)
95 (Nm)
Clutch spring bolts
(Tighten the bolts in several stages, in a criss-cross pattern)
(Tighten the bolts in several stages, in a criss-cross pattern)
8 (Nm)
Final drive
Final drive front sprocket
(Renew the nut)
(Renew the nut)
95 (Nm)
Final drive rear sprocket
(Tighten the nuts in several stages, in a criss-cross pattern)
(Tighten the nuts in several stages, in a criss-cross pattern)
80 (Nm)
Suspension
Note: Always renew stretch bolts and self-locking nuts
Front wheel axle
65 (Nm)
Front wheel axle clamp
23 (Nm)
Rear wheel axle nut
105 (Nm)
Front fork cap
23
General
Motorcycle weight (wet)
182
General
Headlight
(H4)
(H4)
60/55
Engine oil
API SG + JASO MA SAE 10W-50 From -10 °C to 43 °C
Brake fluid
DOT 4
Chain lubricant
Chain Spray
Fork oil
Fork Oil G10 SAE 10W
Front fork
Left fork leg
0.40 Litre
Right fork leg
0.40 Litre
Front fork
Left fork leg
162 Millimetre
Right fork leg
162