Specifications and technical data
Yamaha YFM 350 R Raptor 2WD, 2008, 27 PS, 20 kw
Go to the store - view our offer for
spare parts for Yamaha YFM 350 R Raptor 2WD, 2008, 27 PS, 20 kw
Year of manufacture
2008
No. of cylinders
1
Cylinder capacity
350 cc
Power
27 PS, 20 kw
Specifications and technical data
Engine
Engine speed at maximum power
5750 Revolutions per minute
Number of cylinders
1
Valves per cylinder
2
Engine
Throttle lever free play
3.0 - 5.0 Millimetre
Ignition coil primary resistance
0.018 - 0.28 Ohms
Ignition coil secondary resistance
6320 - 9480 Ohms
Valve clearance
Cold engine
Inlet
0.06 - 0.10 Millimetre
Exhaust
0.16 - 0.20 Millimetre
Idle speed
1450 - 1550 Revolutions per minute
Spark plugs (make and type)
NGK DR8EA
Spark plug gap
0.6 - 0.7 Millimetre
Number of spark plugs
1
Compression pressure
Normal pressure
8.5 (bar)
Minimum pressure
8.0 (bar)
Maximum cylinder head distortion
0.03 Millimetre
Cylinder bore
82.97 - 83.02 Millimetre
Cylinder taper
(Limit)
(Limit)
0.05 Millimetre
Piston diameter
82.92 - 82.97 Millimetre
Piston-to-cylinder clearance
0.04 - 0.06 Millimetre
Piston ring end gap (ring installed)
Top ring
(Standard)
(Standard)
0.2 - 0.4 Millimetre
Top ring
(Limit)
(Limit)
0.5 Millimetre
Second ring
(Standard)
(Standard)
0.2 - 0.4 Millimetre
Second ring
(Limit)
(Limit)
0.5 Millimetre
Oil ring
(Standard)
(Standard)
0.3 - 0.9
Electrical system
Battery type
YTZ10S
Battery capacity
8.6 (Ah)
Battery discharge rate
10 (Hours)
Battery voltage
12
Front disc brakes
Disc thickness, front, minimum
3.0 Millimetre
Brake pad thickness, front, minimum
3.0 Millimetre
Disc run-out, maximum (front)
0.5 Millimetre
Rear disc brakes
Brake pedal height
10 Millimetre
Disc thickness, rear, minimum
3.0 Millimetre
Brake pad thickness, rear, minimum
1.0 Millimetre
Disc run-out, maximum (rear)
0.5
Wheels and tyres
Tyre pressures
Front tyre pressure
0.2 (bar)
Rear tyre pressure
0.2 (bar)
Speed index, minimum
(Based on the maximum speed as listed in the European Type Approval data sheets)
(Based on the maximum speed as listed in the European Type Approval data sheets)
L
Final drive
Final drive chain (make and type)
30 - 40
Engine
Note: Always renew stretch bolts and self-locking nuts
Cylinder head
(Bolts)
(Bolts)
40 (Nm)
Tightening sequence:
(Tighten the bolts in several stages)
(Tighten the bolts in several stages)
Threads lightly oiled
Cylinder head
(Allen bolts)
(Allen bolts)
20 (Nm)
Threads lightly oiled
Cylinder
10 (Nm)
Valve cover
(Renew the O-ring; apply grease to the O-ring)
(Renew the O-ring; apply grease to the O-ring)
10 (Nm)
Crankcase
(Tighten the bolts in several stages, in a criss-cross pattern)
(Tighten the bolts in several stages, in a criss-cross pattern)
10 (Nm)
Apply sealant
Crankcase cover
(Right-hand side)
(Right-hand side)
10 (Nm)
Crankcase cover
(Left-hand side)
(Left-hand side)
10 (Nm)
Renew the gasket
(Renew the washer)
(Renew the washer)
Engine oil drain plug
(Renew the O-ring)
(Renew the O-ring)
32 (Nm)
Spark plugs
17.5 (Nm)
Oil filter
(Cover)
(Cover)
10 (Nm)
Renew the O-ring
Starter motor
10 (Nm)
Camshaft bearing caps
8 (Nm)
Camshaft gearwheel
60 (Nm)
Timing chain tensioner
(Renew the gasket)
(Renew the gasket)
10 (Nm)
Timing chain guide
(Renew the washer)
(Renew the washer)
10 (Nm)
Flywheel
50 (Nm)
Exhaust manifold
(Renew the gasket)
(Renew the gasket)
12 (Nm)
Oil pump
7 (Nm)
Front disc brakes
Brake master cylinder clamp
10 (Nm)
Front brake caliper
28 (Nm)
Brake hose to caliper
(Renew the washer)
(Renew the washer)
27 (Nm)
Front brake disc
28 (Nm)
Rear disc brakes
Rear brake caliper carrier
34 (Nm)
Brake hose to caliper
(Renew the washer)
(Renew the washer)
27 (Nm)
Brake pad retaining pin
18 (Nm)
Clutch system
Clutch
(Renew the nut)
(Renew the nut)
80 (Nm)
Renew the locking washer
Threads lightly oiled
Clutch spring bolts
(Tighten the bolts in several stages, in a criss-cross pattern)
(Tighten the bolts in several stages, in a criss-cross pattern)
8 (Nm)
Final drive
Final drive front sprocket
90 (Nm)
Final drive rear sprocket
(Renew the locking washers)
(Renew the locking washers)
55 (Nm)
Suspension
Note: Always renew stretch bolts and self-locking nuts
Front wheel hub nut
85 (Nm)
Rear wheel hub nut
(Upper)
(Upper)
120 (Nm)
Rear wheel hub nut
(Lower)
(Lower)
73 (Nm)
Rear wheel axle nut
(Apply thread-locking compound)
(Apply thread-locking compound)
160 (Nm)
Wheels and tyres
Wheel nuts
45
General
Motorcycle weight (wet)
180
General
Headlight
30/30
Engine oil
API SE + JASO MA SAE 10W-40
Brake fluid
DOT 4
Gear oil
API GL-5 SAE 80W-90
Gear oil
LS SAE 80W-90
Differential
0.18
Grease
GrLi